CAN Slaves | Tried and tested a million times

Source: Bachmann System Overview catalog | Bachmann electronics GmbH www.bachmann.info.

CANopen has gained and defended its importance in automation for many years; today it is still being further developed and used in numerous applications. The extremely robust data transmission with very low-priced cabling and the large installation base are reasons for the continued success. Bachmann electronic’s compact CAN I / O modules support the homogeneous structure of an automation system through high efficiency and packing density. A screwdriver is all you need to set the network parameters.

Fold out to read more about the CAN Slave module available:

CAN Slave - Digital Input/Output Modules DIOxxx-C

The digital I /O modules DIO16-C, DIO32-C or DIO264-C are stand-alone CAN slave modules with 16, 32 or 64 digital input /output channels.

  • Stand-alone, compact CAN slave module
  • 16/32 channels can be freely configured as input or output
  • Digital outputs each with 1 A continuous current
  • Two internally connected CAN interfaces for loop-through of the cable
  • Galvanic isolation between CAN interfaces and control electronics
  • Baud rate and node ID can be set via rotary switch
  • Supply voltage 18 to 34 VDC
  • Operating range 0 to +60°C without additional cooling
  • Full wiring without additional backplanes
  • Snappable on EN 50022 backplanes

 

See specifications for item:

 

Available accessories for DIOxxx-C:

Terminal set

 Cable CAN

CAN Slave - Analog/ Digital Input/Output Module DA3284-C

Noteworthy compactness and a clever mix of possible signal types are offered by the CAN bus compact module DA3284-C. As a stand-alone fieldbus module (CANopen), the module offers the complete I /O spectrum already integrated for small applications or distributed signal connection points. It is the ideal addition to the familiar family of CAN digital modules and is an optimum »all-in-one« peripheral for small applications, e. g. such as those based on the control terminals CT300 / CT200 from Bachmann electronic. The channel-specific programmable mode (on / off or applied standard signal) enables the unit to be adapted ideally to a wide range of applications without any interface converter. The robust design and processing quality, its outstanding technical specifications, seldom available from the usual fieldbus peripherals, are very impressive.

  • Compact CAN slave I /O module
  • 8 analog inputs ±10 V, ±1 V, Pt100, Pt1000, 0 (4) to 20 mA
  • 4 analog outputs ±10 V or 0 (4) to 20 mA configurable
  • 16 digital inputs • 16 digital inputs or outputs (individually configurable)
  • 2 integrated counter inputs
  • Digital outputs each with 0.5 A continuous current
  • Error detection for digital and analog channels
  • Full wiring without additional backplanes
  • Powerful 32-bit processor for fast cycle times

 

See specifications for item:

 

Available accessories for DA3284-C:

Terminal set

Cable CAN

CAN Slave - Temperature Input/Output Modules TCO2xx-C

The temperature I /O modules, TCO204-C, TCO208-C and TCO216-C are stand-alone CAN slave modules with 4, 8 or 16 thermocouple inputs and 8, 12 or 24 digital outputs.

  • Stand-alone, compact CAN slave module
  • Thermocouple inputs for thermocouple types J and K
  • Measuring range 0 to +500°C/ +800°C configurable
  • Sensor break detection
  • Digital outputs each with 1 A
  • Supply voltage 18 to 34 VDC
  • Operating range 0 to +60°C
  • Snappable on EN 50022 backplanes
  • CAN node ID can be set (hex switch)
  • Baud rate is adjustable (hex switch)

 

See specifications for item:

 

Available accessories for TCO2xx-C:

Terminal set

Cable CAN

CANopen Slave Modules CS200/x

The CS200 / x is the head module for CANopen slave stations. The CS200 / x allows modular CANopen slave stations to be set up from the M1 modules. The same modules that are used for local stations can be used to design a slave station, which simplifies stockkeeping and consistently ensures the same technical data.

  • Head module for CANopen slave stations
  • Up to 30 I / O modules per slave station
  • Optional integrated power supply
  • Transfer rate 10 Kbaud to 1 Mbaud
  • Bus length to 5000 m  (signal repeater required)
  • Two internally connected CAN interfaces for loop-through of the cable
  • Galvanic isolation between CAN interfaces and control electronics
  • Node address can be set via rotary switch
  • 2 serial interfaces (COM 1/2)
  • External 24 V power supply (CS200/N)

 

See specifications for item:

 

Available accessories for CS200/x:

Terminal 03-pin grid

Cable CAN